The IP address 10.0.0.1 is a private IP address. It can be used on the client device or the default IP address of the router. It might be a default gateway address or local client IP address. 10.0.0.1 is often used in commercial computer networks. Home routers usually use addresses in the 192.168. X series, such as 192.168.1.1 or 192.168.0.1. However, computers at home may also be assigned 10.0.0.1 IP addresses. There are more detailed instructions on how to use the 10.0.0.1 IP address below. If your computer's IP address is in the 10.0.0.x range, such as 10.0.0.2, then the router's IP address is most likely to be 10.0.0.1. Some Cisco routers and NETGEAR routers usually use 10.0.0.1 as their default IP address. Connect to 10.0.0.1 IP address If your router's IP address is 10.0.0.1, you can easily connect to it. Open any web browser you like and type http://10.0.0.1 in the address bar. Once the page is loaded, the login page of the router's management console will be opened. You will be asked to enter the administrator user name and password. Private IP addresses can only be accessed from LAN. This means that you can't connect directly to the 10.0.0.1 from outside the network, such as Internet. What is the default username and password of 10.0.0.1 When the router is produced, it has the default username and password. They are usually printed on the back of the router. Here are some of the default usernames and passwords of 10.0.0.1. username: admin, password: password [none]/public [none]/[none] Cisco/Cisco admin/admin cusadmin/highspeed If the default password…

Aug 26, 2018 0Comments 954Browse 0Like Even Read more

192.168.1.2 is the default IP address for some types of home broadband routers. It is a private IP address, and sometimes it is used in a device in the LAN. When the router's IP address is 192.168.1.1, it often assigns 192.168.1.2 to devices on the local network. Working mode of private IP address There is no special meaning or value for a separate private IP address. These are only designated by the Internet digital distribution authority (IANA) as "private". The private IP address is only used for LAN and can not be accessed from Internet. That's why modems and routers can operate easily with default private IP addresses. To access routers from Internet, you must use the public IP address of the router. Connect to router using 192.168.1.2 If your router's IP address is 192.168.1.2, you can log in to its administrative console by typing its IP address into the URL address bar of the web browser: http://192.168.1.2/ At this point, the router will prompt you to enter your username and password. All routers have default user names and passwords by the manufacturer. The most common default user name is "admin", "user" or none. Similarly, the most common passwords are "admin", "password", "123456" or none. The default username and password are usually printed on the bottom of the router. You usually do not need to access the router's administrative console. If your computer has a network connection problem, it may be very useful. 192.168.1.2 is a popular IP address Routers and access point manufacturers must use IP addresses in private scope.…

Aug 25, 2018 0Comments 2652Browse 0Like Even Read more

192.168.1.100 is a private IP address. It is the beginning of the default dynamic IP address range for some Linksys home broadband routers. It can also be allocated to any device on the local network. You can set the IP address of a network device to 192.168.1.100. It can also be used as the default gateway IP address. IP address 192.168.1.100 does not provide better performance and security than any other private address. Most routers use 192.168.1.1 or 192.168.0.1 as their default IP address. Linksys router uses 192.168.1.100 Most Linksys routers set 192.168.1.1 to their default IP address and then assign an address to other network devices via DHCP. Although 192.168.1.100 is usually the default value for a router, administrators can easily change it to a different address (such as 192.168.1.2). The Linksys router supports a configuration setting called "start IP address". It defines the first IP address in the pool that DHCP will allocate from it. The first computer, phone, or other WiFi-connected device that connects to a router is usually assigned this address. If 192.168.1.100 is selected as the starting IP address in the pool, the newly connected device will use the address in that range. Therefore, if 30 devices are allocated, the range is from 192.168.1.100 to 192.168.1.129. In this case, devices in LAN will use 192.168.1.101, 192.168.1.102 and so on. 192.168.1.100 may also be the IP address allocated to the router itself. All connected devices regard it as the default gateway address. In this case, if you need to change the router settings, you must use http://192.168.1.100, then…

Aug 25, 2018 0Comments 3024Browse 0Like Even Read more

The Ping command allows you to specify the computer name instead of the IP address. Users usually like to do Ping on the website by name. Ping a response website In the above image, you can see the result of Ping Google (www.google.com) at the Windows command prompt. Ping reports the target IP address and response time (in milliseconds). Please note that large websites like Google take advantage of many Web server computers around the world. Many different IP addresses (all valid) can be reported on Ping websites. Ping an unresponsive website Many websites (including ufask.com) will prevent Ping requests, which is a kind of network security precaution. The results of Ping on these sites vary, but usually include an error message that the target network cannot access, and there is no useful information. The IP address that blocks Ping's Ping site report is usually the DNS server, rather than the website itself.

Aug 25, 2018 0Comments 1167Browse 0Like Even Read more

Not every Ping is successful, in some cases, the Ping request fails. There are many reasons for this, there are 4 reasons listed below. The IP address specified by the ping program is invalid. Your computer is not connected to the IP network. It does not have its own IP address. No network device is connected to the destination IP address. It means that the IP address of your Ping is not used by a network device. The network between your computer and your target is congested, or Ping is banned by the target device. The above illustration shows a typical Ping session when the program does not receive any response from the target IP address. When the program waits and eventually times out, each reply from the line takes several seconds to appear on the screen. The IP address quoted in each output line of the output is the address of the Ping (host) computer. Intermittent Ping response Although uncommon, Ping may report a response rate other than 0% (no response at all) or 100% (complete response). This usually occurs when the target system is closed (as shown in the example) or when it is started.  

Aug 25, 2018 0Comments 641Browse 0Like Even Read more

This article shows you how to use Ping in Microsoft Windows. If you're not using Windows, the same steps can be applied to other Ping applications. Run Ping command Now there are three mainstream operating systems. They are Microsoft Windows, Mac OS X and Linux. You can run the ping program from the shell command line of the operating system. Ping computers can be sent through IP addresses or names. You can use IP address to Ping computer. Open a shell prompt (in Microsoft Windows, the Command Prompt or MS-DOS Prompt on the Start Menu). Type ping followed by a space and then the IP address. Press the Enter (or Return) key. Explain the result of Ping Reply from: By default, Microsoft Windows Ping sends four messages to this address. The program outputs the confirmation row for each response message received from the target computer. Bytes: By default, the size of each Ping request is 32 bytes. Time: Ping reports the amount of time between sending requests and receiving responses (in milliseconds). TTL: It is the abbreviation of Time to Live. TTL is between 1 and 128 and can be used to calculate the number of networks that Ping messages pass through before reaching the target computer. The value 128 indicates that the device is on the local network and there are 0 other networks. How to run Ping continuously On some computers that use Linux, the standard ping command does not stop running after four request attempts, but runs until the user finishes it. This is very useful for those who want to monitor…

Aug 25, 2018 0Comments 813Browse 0Like Even Read more

192.168.1.254 is a private IP address. It is the default IP address for some home broadband routers and broadband modems. There are many routers that use this IP. Common routers or modems include CenturyLink's 2Wire, Aztech, Billion, Motorola, Netopia, SparkLAN, Thomson, and Westell modems. As a Private IP Addresses The IP address 192.168.1.254 is the private IP address. It is one of the addresses reserved for private networks. This means that devices in this private network cannot be accessed directly from the Internet, but any device on the local network can connect to any other device on the public network. Although the router itself has 192.168.1.254 private IP, it assigns different private IP addresses to any device in its network. All IP addresses on the network should be unique in the network to avoid IP address conflicts. Other common IP addresses used by modem and routers are 192.168.1.100 and 192.168.1.101. How to log in the IP address 192.168.1.254 The default IP address of the router is set in the factory, but you can change it at any time using its administrative interface. Open your favorite web browser and enter http://192.168.1.254 in the Web browser address bar. After entering the user name and password, you can access the router's console. You can change the router's IP address and configure several other options. Default Passwords of 192.168.1.254 All routers have a default username, password and IP address. There are many routers using 192.168.1.254 IP addresses. Here are some common routers and their passwords: 2Wire router: Username: blank, Password: blank Aztech router: Username: "admin",…

Aug 23, 2018 0Comments 905Browse 0Like Even Read more

500 internal server error is a very common HTTP status code. If this code appears, it means that there is a problem with your website and you need to solve it from the Web server. How can you see 500 Internal Server Error You may see 500 internal server error messages in a variety of ways, because each site is allowed to customize the message. Here are some common ways you may see HTTP 500 errors: 500 Internal Server Error HTTP 500 - Internal Server Error Temporary Error (500) Internal Server Error HTTP 500 Internal Error 500 Error HTTP Error 500 500. That's an error Because the site you visit generates 500 Internal Server errors, you can see them in any browser on any operating system, even on your smartphone. In most cases, 500 internal server errors are displayed in the Internet browser window, just like Web pages. Reasons for HTTP 500 error As we mentioned above, the internal server error message indicates that it is usually wrong. In most cases, "error" means that there is a problem with page or website programming, but the problem must exist, and we will investigate it below. Solve the 500 Internal Server Error As we mentioned above, the 500 internal server error is a server side error. This problem may not depend on your computer or Internet connection, but on the server of the website. It's unlikely, but you may have problems. In this case, we will see something you can try: Reload the web page. You can do this by clicking the refresh or reload button,…

Aug 20, 2018 0Comments 850Browse 0Like Even Read more

The IP address 192.168.1.128 is a private IP address. It is not the default address of a router, and the default IP address of a router is usually 192.168.1.1 or 192.168.0.1. 192.168.1.128 as an IP address of PC In a local area network, each network device is connected to each other through a router. The router assigns the IP address to the device in the network. If the router's IP address is 192.168.1.1, it can assign 192.168.1.128 to a PC. The IP address is the only indication of this PC in LAN. If there is a web service deployed on this PC, you can access it through http://192.168.1.128. When it prompts you to enter the password, you need to get it from the owner of the PC. You can also access the shared files of this computer, but what you enter is different. You should type \\192.168.1.128. When it prompts you to enter the password, you also need to get it from the owner of the PC. Because this is the username and password of PC. 192.168.1.128 as an IP address of router No router's default address is this IP address. The two most commonly used default IP addresses for routers are 192.168.1.1 and 192.168.0.1. Of course, you can change the IP address of your router to 192.168.1.128, but you will not normally set this. If you have changed the default address of your router to this IP address. You can find the password in the list below. Linksys Default Password List NETGEAR Default Password List Cisco Default Password List D-Link Default Password List It is…

Aug 19, 2018 0Comments 4822Browse 0Like Even Read more